Active PoE

Internal PoE converter for powering most RouterBOARDs or devices from Ubiquiti with a gigabit LAN port. It is a converter from active power supply known as 802.3af to passive PoE 24V/0.5A with a maximum load of 12W.

MaxLink PI15 is Gigabit PoE injector with very good quality and one output POE port for powering devices supporting 802.3af with maximum power consumption up to 15,4W. The power supply is guided over 4,5 (+) and 7,8 (-) wires. PoE injector is su

MaxLink PI30 is Gigabit PoE injector with very good quality and one output POE port for powering devices supporting 802.3af/at with maximum power consumption up to 30W. The power supply is guided over 4,5 (+) and 7,8 (-) wires. PoE injector is s

USB converter serve to powering any device by USB port. Its converting 802.3af PoE to 5V/2A with 10W maximum load. Example of installation Important note: converter does not convert data from Ethernet to USB, but only power

MaxLink PI60 is a high quality Gigabit POE injector with one POE output port for powering 802.3af/at/bt devices with maximum power consumption up to 60W. For better current load distribution, all 4 pairs of conductors are powered. The

MaxLink PI15S is high quality Gbit POE injector with 1 POE Out eth port for devices which support 802.3af. It provides 15,4W. Plug injector directly to socket. Powering through 4,5(+) and 7,8(-). It is suitable especially for IP cams, VOIP phone

RBGPOE-CON-HP serves as a converter of any 48V PoE source (passive PoE, Telecom PoE, 802.3af and 802.3at) to passive 24V PoE, for example for powering RouterBOARD devices. The PoE converter supports 10/100/1000Mbps. The maximum output power is 24W.

The GPeR unit allows to extend Ethernet cable by additional hop (

Internal cable reduction from Ethernet to USB-C port, which is used for power supply and data transfer and is intended only for the following products from Ubiquiti:

Maxlink POE-CON-AFAT-24 is an indoor PoE converter that changes active power supply to passive. It converts from input PoE 802.3at (44-56V) to passive 24V. Input: 802.3at (44-56V) Output: 24V, max. 1A

The Maxlink 10GBT-1-WM is a simple active PoE injector supporting the 802.3af/at/bt standards as well as 10G Ethernet (10/100M/1/2.5/10G). It features a pair of shielded Ethernet connectors (1x input, 1x output), and power i

Outdoor PoE converter for powering most RouterBOARDs or devices from Ubiquiti with a gigabit LAN port. It is a converter from active power supply known as 802.3af to passive PoE 24V/0.5A with a maximum load of 12W.

TL-POE160S is a very robust Gigabit power PoE injector that supports 802.3af/at standards with power up to 30 W, which is a suitable solution for powering most IP cameras, VoIP, WiFi AP and other devices. The injector has an LED indicatio

S tímto adaptérem můžete napájet Raspberry PI i jiné jednodeskové počítače a další zařízení s napájením přes USB type C konektor. Díky tomu můžete tato zařízení velmi flexibilně použít a nepotřebujeme žádnou zásuvku ani síťový adaptér. Tímto adaptérem ...

MaxLink PI90 is a high-quality Gigabit POE injector with one POE output port for powering 802.3af/at/bt devices with maximum power consumption up to 95W. For better distribution of the current load, all 4 pairs of conductors are powered. Can als

A pair of extenders that allow you to extend PoE over twisted pair or coaxial cables. This solution is ideal for situations where replacing the original cabling is not an option. Each extender features a 1x 10/100 Mbit ETH port and a two-pin con

The Maxlink BT-1-WM is a simple active PoE injector supporting the 802.3af/at/bt standards as well as 2.5G Ethernet (10/100M/1/2.5G). It features a pair of shielded Ethernet connectors (1x input, 1x output), and power is del

MaxLink PI30 is Gigabit PoE injector of white color with very good quality and one output POE port for powering devices supporting 802.3af/at with maximum power consumption up to 30W. The power supply is guided over 4,5 (+) and 7,8 (-) wires. Po

MaxLink MAXPIDIN60 is an active DIN rail mounting PoE injector with DC power input from 12 to 48 V and built in power converter. The output of this power supply is 1Gbit port with support of the 802.3af/at (55 V) which is dedicated for Wi

Cambium Network - Gigabit Poe injector N000900L017B is a high-quality Gigabit PoE injector with one PoE output port for powering devices with voltage level of 56V with a maximum output power of 15W, which is sufficient for the devices such as cnPilot

The GPEN11 is a power injector that can be mounted on a wall, and will power your uplink devices with PoE power. MikroTik GPEN The GPEN11 is part of the GPEN (Giga

The PoE Splitter TL-POE10R fully complies with IEEE 802.3af standard, and can work with all IEEE 802.3af PoE compliant PSE (Power Source Equipment) or PoE Supplier Adapter, such as TP-LINK's TL-SG3424P, TL-SF1008P or TL-POE150S, or other equivalent pro

The Omada 10G PoE++ injector allows you to transmit data and power your devices with a single cable. It includes 1 LAN port with 10Gbps speed as output with PoE and 1 LAN port with 10Gbps speed for input connection. It is fully compliant with 802.3bt/a

The TP-Link POE20E-Outdoor is a rugged outdoor Gbit PoE+ extender with IP68 protection that allows you to extend both data and power by an additional 100 meters at full Gbit speed, delivering up to 30W PoE+ for poweri

The Huawei AD-560062T0E is a Gigabit POE injector with one output POE port for powering devices supporting 802.3af/at with a maximum consumption of up to 35W. The power injector is suitable especially for powering APs, IP cameras, VoIP phones, etc.

TP-Link POE10E PoE extends a PoE/PoE+ network connection an additional 100 m/250 m (10 Mbps mode) from the PoE power sourcing equipment. Supplies up to 20W, which meets the power consumption requirements of most IP cameras.

MaxLink PI60-10G is a high-quality 10-Gigabit PoE injector with a single output PoE port for powering devices that support 802.3af/at standards with a maximum power consumption of up to 60W. To ensure better distribution of the current load, power is s

MaxLink PI60 2x2 is a dual-port PoE injector designed for indoor use. It provides 55 VDC power for remote PDs through one PoE port or delivers 30W per port for two remote PDs simultaneously. It powers terminal devices that support the IEEE802.3af/at st

The MaxLink PI60 EXT 1x4 is a Gigabit PoE extender equipped with 1x input LAN port supporting PoE-IN and 4x output PoE-OUT ports supporting 802.3af/at. The total PoE-OUT budget of the extender is 65W. To power the extender via the PoE-IN port, y

MaxLink PI60 EXT 1x2 is an industrial PoE extender with three 10/100/1000 Mbps ports, 1x PoE-in port supporting 802.3bt/PoE++ with a power output of 60W or higher, up to a maximum of 95W and 2x PoE-out ports providing up to 30W each with