Accessories
Cambium Networks Pole Mount Bracket for cnWave V5000 - Bazar
Mast holder without tilt, mast diameter 25 - 77 mm, for Cambium's cnWave V5000 units
Pigtail cable U.FL/U.FL (IPEX) 25 cm
Propojovací kablík je primárně určen pro wi-fi moduly Turris Omnia k propojení s diplexerem a externí anténou. Lze však použít i s jinými zařízeními, které pracují na max frekvenci 6 GHz; VF kabelová redukce (pigtail) řady U.FL(f) s kabelem RF1.13/0.81...
TP-Link D-HX220 - Wallmount holder for HX-220/HC-200, white
Plastový držák je určený pro uchycení bezdrátových jednotek HX220 a HC220 značky TP-Link na stěnu a to pomocí dvou šroubů. Držák je vyroben z PETG materiálu na 3D tiskárně, má bílou barvu a celkové rozměry jsou 110 x 140 x 40mm.
D-MT750 Rackmount holder for MikroTik devices RB750Gr3, RB750r2, RB750UPr2 and RB760iGS, gray
The plastic holder is designed to hold selected MikroTik products (see below) in 19" and 10" racks. In the case of mounting in a 19" rack, it is possible to mount on the right, left or two holders next to each other. The internal dime
D-MTACX Rackmount holder for MikroTik devices hAP AC2/hAP, gray
Plastový držák je určený pro uchycení vybraných MikroTik produktů (viz níže) do 19" a 10" racku . V případě uchycení do 19" racku je možnost uchycení vpravo, vlevo nebo dvou držáků vedle sebe. Vnitřní rozměry rámečku jsou 119 x 33 mm. Kompatibilní se z...
TP-Link D-M9 Wallmount holder for DECO M9, white
The holder is designed for attaching TP-Link Deco M9 wireless units to a ceiling or wall using a single screw. The holder is made of PETG material on a 3D printer in a white colour.
TP-Link D-EAP6X Holder for EAP devices EAP650 and EAP653, grey
Plastový držák/stojan je určený pro uchycení vybraných TP-Link EAP produktů (viz níže) na stůl či zeď . Pro uchycení držáku na zeď jsou v podstavě o rozměrech 83 x 100 mm vytvořeny 3 otvory. Celkové rozměry držáku jsou 106 x 83 x 153 mm. Kompatibilní s...
Ubiquiti UACC-Lite-AP-AM - Wallmount for U6-Lite, UAP-nanoHD and a UAP-AC-Lite
The plastic wall mount is intended for horizontal installation of Access Points from Ubiquiti, specifically for U6-Lite, UAP-nanoHD and UAP-AC-Lite. The holder is attached to the wall using two screws
Ubiquiti UACC-Pro-AP-AM - Wall mount for U6-Pro and UAP-AC-PRO
The plastic wall holder is intended for horizontal installation of Access Points from Ubiquiti, specifically for U6-Pro and UAP-AC-PRO. The holder is attached to the wall using two screws and dowels, which are in
TP-Link D-EAPOUT Ceiling bracket for EAP610-Outdoor, grey
Plastový stojan pro TP-Link EAP610-Outdoor venkovní WiFi jednotku. Stojan umožňuje instalace na strop (rozměr podstavce je 83x100mm) nebo na stůl. Patice držáku umožňuje bezproblémové držení EAP jednotky, ať už je držák na stole či na stropě. Rozměry d...
TP-Link D-EAPWALL Holder/stand for EAP235-Wall. EAP615-Wall, grey antracit
Plastový stojan pro TP-Link EAP235-Wall a EAP615-Wall WiFi Access point jednotky. Stojan umožňuje instalace na stůl (rozměr podstavce je 81x120mm). Celkové rozměry stojanového držáku jsou 81 x 120 x 88 mm a je vyroben z šedého PETG fillamentu pomocí 3D...
TP-Link D-HaloX Wallmount holder for HALO H70X/H80X, white
Plastový držák je určený pro uchycení bezdrátových jednotek HALO H70X a HALO H80X značky MERCUSYS na stěnu a to pomocí dvou šroubů. Držák je vyroben z PETG materiálu na 3D tiskárně, má bílou barvu a celkové rozměry jsou 135 x 116 x 40mm.
D-U6-L Wallmount holder for Ubiquiti U6-Lite, UAP-nanoHD and UAP-AC-Lite, white
The plastic holder is used for the horizontal installation of UniFi Access Points from Ubiquiti U6-Lite, UAP-nanoHD and UAP-AC-Lite on the wall or as a stand on a table. The holder can be installed with the UniFi plate up and
Ubiquiti case for UAP-beaconHD and U6-Extender, Black design, 3-pack
Set of 3 rectangular covers with black theme is designed to change from the traditional white look and is compatible with UAP-beaconHD devices and U6-Extender. For demanding customers there is a tot
Ubiquiti case for UAP-beaconHD and U6-Extender, Concrete design, 3-pack
Set of 3 rectangular covers with concrete theme is designed to change from the traditional white look and is compatible with UAP-beaconHD devices and U6-Extender. For demanding customers there is a
Ubiquiti case for UAP-beaconHD and U6-Extender, Wood design, 3-pack
Set of 3 rectangular covers with wooden theme is designed to change from the traditional white look and is compatible with UAP-beaconHD devices and U6-Extender. For demanding customers there is a to
D-U6-P Wallmount holder for Ubiquiti U6-PRO and UAP-AC-PRO, white
The plastic holder is used for horizontal installation of UniFi Access Points from Ubiquiti U6-PRO and UAP-AC-PRO on the wall or as a stand on a table. The holder can be installed with the UniFi plate up and down and