Power cables and adapters
Extension cords
AC cables and adapters(10)
DC cables(23)
DC adapters and reductions(10)
Connection between battery(14)
Crimping eye terminal(4)
Cable adapter from UPS (IEC C14) to 1 socket 230V, 30cm
Cable reduction with 1 power socket for connection to UPS with IEC connectors. Completely product length is 30 cm.
Pressing connector GF-M8, 8mm hole, yellow isolation
Průřez vodiče 4,0 - 6,0 mm2; Materiál: elektrolytická měď, pocínovaný; PVC izolace, s rozšířenou izolační objímkou, vhodný pro harmonizované kabely
Teltonika 4 pin power cable with screw terminal, 2m
Teltonika 2m power supply cable terminated at one end with a 4-pin connector and at the other end with a screw terminal block. The cable is primarily intended for powering the following Teltonika devices: RUT230
Ubiquiti UniFi Smart Power Cable, USP-Cable
USP-Cable is a special DC power cable designed for the Ubiquiti SmartPower System. This cable connecting UniFi Switch and the UniFi SmartPower (USP-RPS) from which it will receive power if the built-in power source fails. The cable is 1.5m l
Reduction jack / terminal, MALE standard DC 2.1 / 5.5 power connector (for CCTV cameras)
Adapter from a two-pole terminal block to standard DC jack with size 2.1/5.5mm. Adapter is suitable for powering analog cameras or other devices without PoE technology. Just bring a two line DC cable and simply connect it to the terminal block m
MaxLink power cord 230V, 3-conductor, 1.2m, tinned connectors, CZ standard
3-conductor power cord with shielded tinned end of the wires on one side. It is a cable designed to connect industrial power resources to the power supply. This cable has 0.5m length of and match the Czech version (brown lead is connected to the
1.5 m DC cable (with 2.1/5.5 connector) straight
POZOR !!!; Před připojením je nutné zkontrolovat polarizaci kabelu. SPECIFIKACE; Typ konektoru: O 2.1 / 5.5 mm Třída kabelu; Připevňování vodiče: Pájení; Délka kabelu: 1.5 m; Určení: Elektrický kabel; Materiál: PET; Příklad použití: • OMY-2X0.75; • K-6...
Reduction of DC power, converts the DC jack 2.1 mm to 2.5 mm - straight
Redukce pro DC zdroje, konvertuje 2.1mm DC jack na 2.5mm DC plug (z 2.1mm adaptéru redukuje na 2.5mm přístroj), rovná, 180 stupňů. Redukce je vhodná například pro APU.1C1, APU.1C4, APU.1D4.
Teltonika PR4MK04K 4-Pin terminal
4-pin socket with contact terminal for Teltonika devices.
DC-DC cable between batteries, 15cm, 2x M6 hole
The DC link cable terminated by ears on both sides is ideal for connecting M6 threaded batteries. By connecting multiple batteries, you can increase the output voltage (serial connection) or total capacity (parallel connection). The cable is made of a
Power splitter ACB-2CH, 2x male, 1x female
Rozbočovací kabel DC napájení s konektory 2x samec (male) na 1x samice (female). Konektory mají rozměry 2.1/5.5mm a celková délka je 19cm.
DC-DC cable between battery and power source, 90cm, M6 hole - wire end
An end-to-end DC connecting cable with one ear on the first side and with socket on the other is ideal for connecting a M6 threaded battery and a voltage converter. The cable is made of a sufficiently dimensioned cable with a cross-section of 4mm2 (cur
CEE7 to UK/IRL plug adapter CP1
Fused at 3A, Voltage: 220-250V Max load: 600W Simple, safe and fast method of plug conversion Approved to BS5733, BS1363-5 plug/socket features and BS1362 fuse link Colour: Black
Teltonika PR5MEC21 - 4-Pin Power Adapter With I/O Access
Teltonika PR5MEC21 is adapter intended mainly for routers from Teltonika. The adapter enables control using IoT devices like as Raspberry Pi, etc.
Teltonika PR2PD01B - 4-Pin to Barrel Socket Adapter
Adapter from 5.5 x 2.1 to 4-pin. Length is 10 cm
Ubiquiti UniFi Smart Power Cable, USP-Cable - Bazar
The product is new and unused. Only damaged packaging. USP-Cable is a special DC power cable designed for the Ubiquiti SmartPower System. This cable connecting UniFi Switch and the UniFi SmartPower (
Ubiquiti C13-C14, power cable
Power connection cable C13 - C14. It is typically used to connect a UPS backup power source and a device that needs to remain powered in the event of a power outage.
DC-DC cable between battery and power source, 120cm, M6 hole - wire end
An end-to-end DC connecting cable with one ear on the first side and with socket on the other is ideal for connecting a M6 threaded battery and a voltage converter. The cable is made of a sufficiently dimensioned cable with a cross-section of 4mm2 (cur
DC-DC cable between batteries, 15cm, 2x M8 hole
The DC link cable terminated by ears on both sides is ideal for connecting M8 threaded batteries. By connecting multiple batteries, you can increase the output voltage (serial connection) or total capacity (parallel connection). The cable is made of a
DC-DC cable between batteries, 30cm, 2x M8 hole
The DC link cable terminated by ears on both sides is ideal for connecting M8 threaded batteries. By connecting multiple batteries, you can increase the output voltage (serial connection) or total capacity (parallel connection). The cable is made of a
DC-DC cable between battery and power source, 30cm, M8 hole - wire end
An end-to-end DC connecting cable with one ear on the first side and with socket on the other is ideal for connecting a M8 threaded battery and a voltage converter. The cable is made of a sufficiently dimensioned cable with a cross-section of 4mm2 (cur
DC-DC cable between battery and power source, 60cm, M8 hole - wire end
An end-to-end DC connecting cable with one ear on the first side and with socket on the other is ideal for connecting a M8 threaded battery and a voltage converter. The cable is made of a sufficiently dimensioned cable with a cross-section of 4mm2 (cur
DC-DC cable between battery and power source, 90cm, M8 hole - wire end
An end-to-end DC connecting cable with one ear on the first side and with socket on the other is ideal for connecting a M8 threaded battery and a voltage converter. The cable is made of a sufficiently dimensioned cable with a cross-section of 4mm2 (cur
DC-DC cable between battery and power source, 120cm, M8 hole - wire end
An end-to-end DC connecting cable with one ear on the first side and with socket on the other is ideal for connecting a M8 threaded battery and a voltage converter. The cable is made of a sufficiently dimensioned cable with a cross-section of 4mm2 (cur
Napájecí kabel s vypínačem pro světlo do rozvaděče
Power cable with a switch, featuring a DC female connector 5.5 / 2.1 mm on the input side and bare contacts on the output side. Cable is 22AWG, switch with a current limit of 2A. Total cable length 150 cm: 100 cm DC connector t
Maxlink adapter for UPS(3 sockets), max. 250V, 10A, length 30cm
Cable adapter with three sockets for connection to UPS with IEC connectors. Specifications Cable length 30 cm Max. operating current 10 A Nominal voltage 250 V IEC C14 plug CEE 7/3 (F)
Cover conectors M5-M8 black
Krytka na mínusovou svorku autobaterie. Pólová krytka slouží jako ochrana proti zkratu baterie při manipulaci s baterií. Užitečná například při nechtěnném kontaktu s kovovým nářadím při provádění výměny baterie, ale také před vlivy koroze, oxidace a ag...
Conectors cover M5-M8 red
Krytka na plusovou svorku autobaterie. Pólová krytka slouží jako ochrana proti zkratu baterie při manipulaci s baterií. Užitečná například při nechtěnném kontaktu s kovovým nářadím při provádění výměny baterie, ale také před vlivy koroze, oxidace a agr...
Cambium Networks AC Power Line Cord, Type C5, 720mm with EU plug
Cambium Networks AC Power Line Cord Type of cable - power cable 230V / 10A Connector type 1 - EURO Plug (10A) Connector type 2 - IEC320 C5 Colour - black Lenght - 0.72 m
Reduction of DC power, converts the DC jack 5,5x2,5mm na 4x1,7mm - straight
Redukce pro DC zdroje, konvertuje klasický napájecí konektor 5,5 x 2,5mm na 4x1,7mm. Redukce je vhodná například pro mini PC Orange Pi, Banana Pi, Wintel, konzole PSP, některé vnitřní kamery a chůvičky a další.

