Accessories

The holder is designed for attaching TP-Link Deco M5 and P7 wireless units to a ceiling or wall using a single screw. The holder is made of PETG material on a 3D printer in a white colour.

The holder is designed to attach TP-Link Deco E4 and M4 wireless units to the wall using two screws. The holder is made of PETG material on a 3D printer in a white colour.

The plastic wall mount is designed to mount Halo H50 / H30 / S12 / S3 Mesh Access Points from Mercusys. The holder is made using 3D printing, has a white color and its dimensions are 123 × 40 × 91mm.

The holder is designed to attach TP-Link Deco X20, Deco X50 and X60 wireless units to the wall using two screws. The holder is made of PETG material on a 3D printer and the colour is white.

The plastic holder is designed to hold selected TP-Link products (see below) in 19" and 10" racks. In the case of mounting in a 19" rack, it is possible to mount on the right, left or two holders next to each other. The internal dime

The plastic holder is designed to hold selected TP-Link products (see below) in 19" and 10" racks. In the case of mounting in a 19" rack, it is possible to mount on the right, left or two holders next to each other. The internal dime

The plastic holder is designed to mount the UCK-G2-PLUS from Ubiquiti to 19" and 10" racks. In the case of mounting in a 19" rack, it is possible to mount on the right, left or two holders next to each other.

The connecting cable is primarily intended for Turris Omnia wi-fi modules to connect with a diplexer and an external antenna. However, it can also be used with other devices that operate at a maximum frequency of 6 GHz VF cable reduction (pig

The connecting cable is primarily intended for Turris Omnia wi-fi modules to connect with a diplexer and an external antenna. However, it can also be used with other devices that operate at a maximum frequency of 6 GHz VF cable reduction (pig

The connecting cable is primarily intended for Turris Omnia wi-fi modules to connect with a diplexer and an external antenna. However, it can also be used with other devices that operate at a maximum frequency of 6 GHz VF cable reduction (pig

The plastic holder/stand is designed to mount selected TP-Link EAP products (see below) on a table or wall. 3 holes are made in the base measuring 83 × 100 mm to attach the bracket to the wall. The overall dimensions of the holder are

The plastic holder is designed to hold selected MikroTik products (see below) in 19" and 10" racks. In the case of mounting in a 19" rack, it is possible to mount on the right, left or two holders next to each other. The internal dime

Plastový držák je určený pro uchycení vybraných MikroTik produktů (viz níže) do 19" a 10" racku . V případě uchycení do 19" racku je možnost uchycení vpravo, vlevo nebo dvou držáků vedle sebe. Vnitřní rozměry rámečku jsou 119 x 33 mm. Kompatibilní se z...

The holder is designed for attaching TP-Link Deco M9 wireless units to a ceiling or wall using a single screw. The holder is made of PETG material on a 3D printer in a white colour.

Plastový držák/stojan je určený pro uchycení vybraných TP-Link EAP produktů (viz níže) na stůl či zeď . Pro uchycení držáku na zeď jsou v podstavě o rozměrech 83 x 100 mm vytvořeny 3 otvory. Celkové rozměry držáku jsou 106 x 83 x 153 mm. Kompatibilní s...

The plastic wall mount is intended for horizontal installation of Access Points from Ubiquiti, specifically for U6-Lite, UAP-nanoHD and UAP-AC-Lite. The holder is attached to the wall using two screws

The plastic wall holder is intended for horizontal installation of Access Points from Ubiquiti, specifically for U6-Pro and UAP-AC-PRO. The holder is attached to the wall using two screws and dowels, which are in

Plastový stojan pro TP-Link EAP610-Outdoor venkovní WiFi jednotku. Stojan umožňuje instalace na strop (rozměr podstavce je 83x100mm) nebo na stůl. Patice držáku umožňuje bezproblémové držení EAP jednotky, ať už je držák na stole či na stropě. Rozměry d...

Plastový stojan pro TP-Link EAP235-Wall a EAP615-Wall WiFi Access point jednotky. Stojan umožňuje instalace na stůl (rozměr podstavce je 81x120mm). Celkové rozměry stojanového držáku jsou 81 x 120 x 88 mm a je vyroben z šedého PETG fillamentu pomocí 3D...

Plastový držák je určený pro uchycení bezdrátových jednotek HALO H70X a HALO H80X značky MERCUSYS na stěnu a to pomocí dvou šroubů. Držák je vyroben z PETG materiálu na 3D tiskárně, má bílou barvu a celkové rozměry jsou 135 x 116 x 40mm.

The plastic holder is used for the horizontal installation of UniFi Access Points from Ubiquiti U6+, U6-Lite, UAP-nanoHD and UAP-AC-Lite on the wall or as a stand on a table. The holder can be installed with the UniFi plate up

Set of 3 rectangular covers with black theme is designed to change from the traditional white look and is compatible with UAP-beaconHD devices and U6-Extender. For demanding customers there is a tot

Set of 3 rectangular covers with concrete theme is designed to change from the traditional white look and is compatible with UAP-beaconHD devices and U6-Extender. For demanding customers there is a

Set of 3 rectangular covers with wooden theme is designed to change from the traditional white look and is compatible with UAP-beaconHD devices and U6-Extender. For demanding customers there is a to

The plastic holder is used for horizontal installation of UniFi Access Points from Ubiquiti U6-PRO and UAP-AC-PRO on the wall or as a stand on a table. The holder can be installed with the UniFi plate up and down and

Wireless set of two adhesive antennas with pigtails terminated with u.Fl connectors and Dual Band WiFi 6 cards with Mediatek MT7915DAN chipset, miniPCI-e bus with 2x u.Fl connectors, supporting WPA2 encryption, modulation speed

Wireless set of two pigtails terminated with u.Fl connectors, omnidirectional antennas, upper part of aluminum chassis in silver color on Turris Omnii and Dual Band WiFi 6 cards marked AW7915-NP1, miniPCI-e bus with 4× u.Fl connectors

Product condition: Used piece for exhibition purposes. Fully functional. Mast holder without tilt, mast diameter 25 - 77 mm, for Cambium's cnWave V5000 units

Propojovací kablík je primárně určen pro wi-fi moduly Turris Omnia k propojení s diplexerem a externí anténou. Lze však použít i s jinými zařízeními, které pracují na max frekvenci 6 GHz; VF kabelová redukce (pigtail) řady U.FL(f) s kabelem RF1.13/0.81...

Plastový držák je určený pro uchycení bezdrátových jednotek HX220 a HC220 značky TP-Link na stěnu a to pomocí dvou šroubů. Držák je vyroben z PETG materiálu na 3D tiskárně, má bílou barvu a celkové rozměry jsou 110 x 140 x 40mm.