Accessories

The new MikroTik Gigabit PoE adapter for powering any RouterBOARD over Gigabit Ethernet. Simply connect your power source and then use an ethernet cable to connect the injector to the RouterBOARD device. Helps reducing number of wires

48V 2A 96W power supply, to be used with MikroTik products that support 48V POE output, like hEX PoE and CRS112-8P-4S-IN. It’s providing 30% more current than the old model 48POW (48V 1.46A 70W), allowing more power per port. Co

RBGPOE-CON-HP serves as a converter of any 48V PoE source (passive PoE, Telecom PoE, 802.3af and 802.3at) to passive 24V PoE, for example for powering RouterBOARD devices. The PoE converter supports 10/100/1000Mbps. The maximum output power is 24W.

Odrušovač pro MikroTik RB wAP snižuje nežádoucí interferenční rušení ze zadní strany a z bočních stran. Ochraňuje signál jen v žádoucí oblasti. Odrušovač spolu se zadním krytem nezvyšuje zisk antény, avšak výrazně snižuje nežádoucí rušení a díky tomu z...

A super low loss 50cm long RPSMA cable for superior connection quality, suited for indoor and outdoor use, this cable provides superior matching and loss values. The name of this cable comes from combining the words “flexible” and “waveguide”

ACGPSA is standalone active GPS antenna, that works in 1575.4 MHz spectrum. Antenna size is 46.5mm x 26.5mm x 12.5mm with IP67 rating and includes internal magnet and double sided tape, so it can easily be attached to various surfaces. It

Power adapter with output voltage 48V DC, maximum current 0.95A, total output power 45,6W and connector 5.5 / 2.1mm. The power source is part of the MikroTik GPEN concept, which provides all the benefits of GPON.

Power adapter with output voltage 57V DC, maximum current 0.8A, total output power 45,6W and connector 5.5 / 2.1mm. The power source is part of the MikroTik GPEN concept, which provides all the benefits of GPON.

The GPEN21 is a smart power injector that serves as an advanced software controlled repeater. Not only can it power your uplink devices via PoE, it can also provide a range of useful software features: Interface management + monitoring

The GPeR unit allows to extend Ethernet cable by additional hop (

U.fl-SMA female pigtail, that can be used to connect your LTE card to an external antenna if you are using wAP R kit (there are special openings in the enclosure of the wAP R, designed for these pigtails)

nRayAIM-DH1 is an alignment and aiming attachment for the nRAY. Use it to attach a scope of your choice for even greater precision and easier installation of the Wireless Wire nRAY. *Scope is not included.

A white power adapter with direct installation into a socket with an output voltage of 5V DC, a maximum current of 2.4A, a total output power of 12W and a USB-C connector. The input plug to the socket is EU type.

Professional high-frequency SMASMA cable from MikroTik designed for use in the LTE industry, for example for connecting LTE CPE unit and an LTE antenna. The 1m cable is terminated with two SMA male connectors. For better protection agains

You can’t buy safety, but you can buy an RBGESP surge protector and keep your setup safe. RBGESP is Gigabit Ethernet Surge Protector that can be used to protect the network from lightning or surge damages. Here’s what a typical use-case would

Outdoor AC/DC power supply in a durable metal chassis with output voltage 26 V, max. output current 9.4 A, total power 250 W suitable for a series of netPower products from MikroTik. The chassis is IP67 certified with extra protec

12POW150 is replacement Hot Swap power source for MikroTik CCR1072-1G-8S+. Total output power is 150W.

We are now offering a Hot Swap -48V DC telecom power supply (product code PW48V-12V150W), available to purchase separately for use with CCR1072. Simply remove one of the current power supplies and replace with the new PW48V-12V150W for -48V installatio

MikroTik 24V2APOW is a replacement internal power supply that is specially designed for some MikroTik devices. Total power is 60W at 24V and 2.5A max. current. Compatibility with these models CCR1009-7G-1C-1S+ CRS31

Original MikroTik power adapter with direct installation in a socket with a standard 5.5 / 2.1mm connector designed for powering, for example MikroTik devices with input voltage 24V DC. The power adapter has a maximum power 19W and

MikroTik GB60A-S12 is a replacement internal power supply that is specially designed for some MikroTik devices. Total power is 60W at 12V and 5A max. current. Compatible with CCR1016 r2 models

MikroTik UP1302C-12 is a replacement internal power supply that is specially designed for some MikroTik devices. Total power is 130W at 12V and 10.8A max. current. Compatibility list CCR1036-8G-2S+EM (rev. 2) CCR1

MikroTik power adapter with 5V voltage, maximum current 1A, max. Power 5W and microUSB connector. This power source is suitable, for example, for MikroTik hAP mini, hAP lite and cAP lite.

Cable reduction from MMCX to RSMA female, 26 cm long, intended for the frequency band from 2 to 6 GHz. The MMCX connector is angled and the RSMA female is straight. This is a high-quality connection, e.g. in BaseBox2 or BaseBox5 devic

The CWDM is a passive MUX/DEMUX unit, which allows to combine up to eight fiber links into one, to simplify and reduce the cost of long distance fiber installations. At the other location, the combined line is split back up again, so that instead of ei

The MikroTik CWDM-CHASSIS-2 is a metal 1U chassis made for 19" data cabinet with two slots for 8-port MUX / DEMUX modules (CWDM-MUX8A).

DINrail PRO is a mounting bracket for LtAP mini series products, designed to fit standard 35 mm × 7.5 mm DIN rails. This bracket will allow to install LtAP mini next to the industrial control equipment like water meters etc., as well as in equipment ra

±48 V DC telecom Open Frame Power supply with 12 V 8 A output, for use with new “r2” revision of Cloud Core Routers. Simply remove one of the current power supplies and replace with the new PW48V-12V85W for -48 V installations. Compatibility

The GPEN11 is a power injector that can be mounted on a wall, and will power your uplink devices with PoE power. MikroTik GPEN The GPEN11 is part of the GPEN (Giga

Outdoor AC/DC power supply in a durable metal chassis with output voltage 53 V, max. output current 4.7 A, total power 250 W suitable for a series of netPower products from MikroTik. The chassis is IP67 certified with extra protec