Accessories

nRayAIM-DH1 is an alignment and aiming attachment for the nRAY. Use it to attach a scope of your choice for even greater precision and easier installation of the Wireless Wire nRAY. *Scope is not included.

MikroTik power adapter with 5V voltage, maximum current 1A, max. Power 5W and microUSB connector. This power source is suitable, for example, for MikroTik hAP mini, hAP lite and cAP lite.

Cable reduction from MMCX to RSMA female, 26 cm long, intended for the frequency band from 2 to 6 GHz. The MMCX connector is angled and the RSMA female is straight. This is a high-quality connection, e.g. in BaseBox2 or BaseBox5 devic

The CWDM is a passive MUX/DEMUX unit, which allows to combine up to eight fiber links into one, to simplify and reduce the cost of long distance fiber installations. At the other location, the combined line is split back up again, so that instead of ei

±48 V DC telecom Open Frame Power supply with 12 V 8 A output, for use with new “r2” revision of Cloud Core Routers. Simply remove one of the current power supplies and replace with the new PW48V-12V85W for -48 V installations. Compatibility

The GPEN11 is a power injector that can be mounted on a wall, and will power your uplink devices with PoE power. MikroTik GPEN The GPEN11 is part of the GPEN (Giga

Low-cost passive PoE base unit for powering passive PoE devices over ethernet. Simply connect your power source to the injector, and then use an ethernet cable to connect the injector to the RouterBOARD device. Helps reducing number of wires that lead

RBGPOE-CON-HP serves as a converter of any 48V PoE source (passive PoE, Telecom PoE, 802.3af and 802.3at) to passive 24V PoE, for example for powering RouterBOARD devices. The PoE converter supports 10/100/1000Mbps. The maximum output power is 24W.

ODR-OmniTik is an interference suppression cover made from stainless steel with a thickness of 0.8 mm designed for MikroTik OmniTik U/UPA units. This cover reduces unwanted interference, reducing noise, increasing connection stabil

Odrušovač pro MikroTik RouterBOARD SEXTANTG-5HPnD snižuje nežádoucí interferenční rušení ze zadní strany a z bočních stran. Ochraňuje signál jen v žádoucí oblasti. Odrušovač spolu se zadním krytem nezvyšuje zisk antény, avšak výrazně snižuje nežádoucí ...

The Sleeve30 kit for mANT30 parabolic antenna will enhance point-to-point link performance by reducing noise and will also reduce impact on adjacent RF devices by removing the side radiation from the antenna. Sleeve30 Kit also reduces

12POW150 is replacement Hot Swap power source for MikroTik CCR1072-1G-8S+. Total output power is 150W.

We are now offering a Hot Swap -48V DC telecom power supply (product code PW48V-12V150W), available to purchase separately for use with CCR1072. Simply remove one of the current power supplies and replace with the new PW48V-12V150W for -48V installatio

MikroTik 24V2APOW is a replacement internal power supply that is specially designed for some MikroTik devices. Total power is 60W at 24V and 2.5A max. current. Compatibility with these models CCR1009-7G-1C-1S+ CRS31

ACGPSA is standalone active GPS antenna, that works in 1575.4 MHz spectrum. Antenna size is 46.5mm x 26.5mm x 12.5mm with IP67 rating and includes internal magnet and double sided tape, so it can easily be attached to various surfaces. It