Accessories

UbiBracket is universal positioning mount for mast or wall for all NanoStation and Loco devices. The holder can be attached to a pipe up to a diameter of 60mm.

The Universal Arm Bracket is designed for convenient wall or pole mounting of the NanoStation®M. 90° tilt adjustment allows for easy positioning.

RJ45 Waterproof kit is a cable gland Ethernet kit for separating indoor and outdoor cabling when mounting in any mounting box. On the outside there is a keystone with an RJ45 connector and on the inside there is a 20cm FTP cable with a shielded TP cabl

The elegant aluminum stand with non-slip feet is only for the Cloud Key G2 Plus from Ubiquiti, which will hold the controller in an upright position. The dimensions of the base are 134 x 72 mm.

WiFiMan Wizard is a portable spectral analyzer designed for the WiFiMan iOS and Android mobile application with which it communicates wirelessly via Bluetooth. Together with a Lidar-equipped smartphone, it is able to project t

nHD-cover-Black-3 is a set of 3 covers for UAP-nanoHD, U6 Lite, U6+ and *UAP-AC-LITE with Black design. For demanding customers is available up to 6 optional skins allow the UniFi AP to blend into its surroundings. Cover for UAP-AC-LITE i

nHD-cover-Concrete-3 is a set of 3 covers for UAP-nanoHD, U6 Lite, U6+ and *UAP-AC-LITE with Concrete design. For demanding customers is available up to 6 optional skins allow the UniFi AP to blend into its surroundings. Cover for UAP-AC-

Twin Horn Bracket allows you to install two symmetrical Horn antennas with exactly the same alignment. The bracket also accommodates mainstream 4x4 radios, such as ePMP™ 3000 or Mimosa® A5c. High density sectors or 4x4 deployments are now ingeniously s

The 5 GHz RocketDish to airFiber® Antenna Conversion Kit, model AF-5G-OMT-S45, converts the RocketDish RD-5G30 or RD-5G34 antenna for use with the airFiber AF-5X radio.

The plastic wall holder is intended for horizontal installation of Access Points from Ubiquiti, specifically for U6-Pro and UAP-AC-PRO. The holder is attached to the wall using two screws and dowels, which are in

The plastic holder/stand is designed to mount selected TP-Link EAP products (see below) on a table or wall. 3 holes are made in the base measuring 83 × 100 mm to attach the bracket to the wall. The overall dimensions of the holder are

The holder is designed for attaching TP-Link Deco M5 and P7 wireless units to a ceiling or wall using a single screw. The holder is made of PETG material on a 3D printer in a white colour.

Precise GPS Synchronization Using a common GPS timing reference, the airFiber X radios work cohesively to deliver powerful, multi-Gigabit bridging performance for PtP links. 4x4 M

Turris Omnia diplexer is a spare part intended for cases where the original diplexer has been broken due to careless handling. Used to merge the signal from two cards (2.4 and 5 GHz) into one RP-SMA connector. Package contents

The MOX PoE add-on can be used to provide power to the Turris MOX router over ethernet without having to use a separate power cable. It connects to the MOX A (Basic) module which is part of all MOX configurations. It is compliant with IEEE standards 80

RTROM01-RM is a set of two metal mounts intended for mounting the Turris Omnia 2020 in a 19" rack. Due to a different mount it is not possible to use this rack mount kit also for the Turris Omnia 2019. Double-sided router mounting T

The Dual Band WiFi 6 card model AW7915-NP1 features a miniPCI-e interface with 4 × u.Fl connectors, supporting WPA3 encryption and modulation speeds of 2401 Mbps in the 5 GHz band (4×4) or 574 Mbps in the 2.4 GHz band with

Wireless set of two adhesive antennas with pigtails terminated with u.Fl connectors and Dual Band WiFi 6 cards with Mediatek MT7915DAN chipset, miniPCI-e bus with 2x u.Fl connectors, supporting WPA2 encryption, modulation speed

With the help of the Turris Omnia LTE kit your Omnia will be able to connect to connectivity using LTE category 6, enabling a transfer rate of 300/50 Mbps (Down/Up). The kit is built on a miniPCI card with a Quectel EP-06 modem

The 60 GHz Precision Alignment Mount enhances mounting flexibility and device alignment. It features an easy-to-use design that requires only an Allen wrench (included) to align.

The plastic holder is designed to hold selected MikroTik products (see below) in 19" and 10" racks. In the case of mounting in a 19" rack, it is possible to mount on the right, left or two holders next to each other. The internal dime

nHD-cover-Wood-3 is a set of 3 covers for UAP-nanoHD, U6 Lite, U6+ and *UAP-AC-LITE with Wood design. For demanding customers is available up to 6 optional skins allow the UniFi AP to blend into its surroundings. Cover for UAP-AC-LITE is n

IW-HD-BK-3 is a set of 3 covers for Ubiquiti UAP In-Wall HD with a black theme. For demanding customers, there are a total of 5 optional cover designs to choose from.

Precision Alignment Kit to better attach the antenna. Precision two-axis alignment enhances beam directivity for maximum PtP or backhaul performance. Applies to the following models airFiber®AF-5G30-S45 PowerBeam ™

This plastic mounting box made of PVC material is suitable for installing the UniFi AP In Wall model in a plasterboard wall. For proper holding in plasterboard, 2 screws in opposite corners with plastic flags serve as a support against sliding the box

The holder is designed to attach TP-Link Deco E4 and M4 wireless units to the wall using two screws. The holder is made of PETG material on a 3D printer in a white colour.

The holder is designed to attach TP-Link Deco X20, Deco X50 and X60 wireless units to the wall using two screws. The holder is made of PETG material on a 3D printer and the colour is white.

The plastic holder is designed to hold selected TP-Link products (see below) in 19" and 10" racks. In the case of mounting in a 19" rack, it is possible to mount on the right, left or two holders next to each other. The internal dime

The plastic holder is designed to mount the UCK-G2-PLUS from Ubiquiti to 19" and 10" racks. In the case of mounting in a 19" rack, it is possible to mount on the right, left or two holders next to each other.

The connecting cable is primarily intended for Turris Omnia wi-fi modules to connect with a diplexer and an external antenna. However, it can also be used with other devices that operate at a maximum frequency of 6 GHz VF cable reduction (pig