Active PoE

The Maxlink 10GBT-1-WM is a simple active PoE injector supporting the 802.3af/at/bt standards as well as 10G Ethernet (10/100M/1/2.5/10G). It features a pair of shielded Ethernet connectors (1x input, 1x output), and power i

The GPEN11 is a power injector that can be mounted on a wall, and will power your uplink devices with PoE power. MikroTik GPEN The GPEN11 is part of the GPEN (Giga

Internal PoE extractor for powering most RouterBOARDs or Ubiquiti devices. It is a converter from active power supply designated as 802.3af to passive PoE 18V/0.7A with a maximum load of 12.8W.

Outdoor PoE extractor for powering most RouterBOARDs or Ubiquiti devices. It is a converter from active power supply designated as 802.3af to passive PoE 18V/0.7A with a maximum load of 12.8W.

MaxLink PI30F is a high-quality Gigabit POE injector with a single POE port, LAN port and one SFP port for powering 802.3af/at devices with maximum power consumption up to 30W. For better distribution of current load, power is applied to

MaxLink PI90 is a high-quality Gigabit POE injector with one POE output port for powering 802.3af/at/bt devices with maximum power consumption up to 95W. For better distribution of the current load, all 4 pairs of conductors are powered. Can als

POE-PAN4-GB-AF/A is a Gigabit active PoE injector that is suitable for powering up to 4 devices, such as IP cameras, VoIP or other devices with support for 802.3af/at standards with a maximum power consumption of 30 W. Ethernet por

With this adapter, you can power Raspberry PI (all models), other single-board computers, and other devices powered by the Micro USB connector. This allows you to use these devices very flexibly and we don't need a power outlet or AC adapter. T

Maxlink POE-CON-AFAT-24 is an indoor PoE converter that changes active power supply to passive. It converts from input PoE 802.3at (44-56V) to passive 24V. Input: 802.3at (44-56V) Output: 24V, max. 1A

The Huawei AD-560062T0E is a Gigabit POE injector with one output POE port for powering devices supporting 802.3af/at with a maximum consumption of up to 35W. The power injector is suitable especially for powering APs, IP cameras, VoIP phones, etc.

TP-Link POE10E PoE extends a PoE/PoE+ network connection an additional 100 m/250 m (10 Mbps mode) from the PoE power sourcing equipment. Supplies up to 20W, which meets the power consumption requirements of most IP cameras.

MaxLink PI60-10G is a high-quality 10-Gigabit PoE injector with a single output PoE port for powering devices that support 802.3af/at standards with a maximum power consumption of up to 60W. To ensure better distribution of the current load, power is s

MaxLink PI60 2x2 is a dual-port PoE injector designed for indoor use. It provides 55 VDC power for remote PDs through one PoE port or delivers 30W per port for two remote PDs simultaneously. It powers terminal devices that support the IEEE802.3af/at st

MaxLink MAXPI15FE is a very simple 100Mbps PoE injector with one output POE port to power devices with 802.3af support with maximum consumption up to 24W, output voltage 48V and current 0.5A. The ma

Cable extender equipped with TransPort connectors is intended for coupling UISP TransPort cables in outdoor. Mounting is possible to the mast / pole with diameter 35mm - 60mm.

MaxLink PI30 is Gigabit PoE injector of white color with very good quality and one output POE port for powering devices supporting 802.3af/at with maximum power consumption up to 30W. The power supply is guided over 4,5 (+) and 7,8 (-) wires. Po