Mounting brackets

The holder is designed for attaching TP-Link Deco M5 and P7 wireless units to a ceiling or wall using a single screw. The holder is made of PETG material on a 3D printer in a white colour.

The Ubiquiti U7 Pro Wall Table Stand is an elegant and very light table stand for the Ubiquiti U7 Pro Wall device.

The holder is designed for attaching TP-Link DECO BE65 wireless units to the wall using 2 screws. The holder is made of PETG material on a 3D printer in a white colour.

The holder is designed for attaching TP-Link switches to a DIN rail holder. It is made of PETG material on a 3D printer in a grey anthracite color. Dimensions: 101x25mm Compatible products: SG108xx, SF1006P, ER605, RP1

The holder is designed for attaching TP-Link switches to a DIN rail holder. It is made of PETG material on a 3D printer in a grey anthracite color. Dimensions: 98x25mm Compatible products: OC200, SF1005xx, SG105xx, SG1

Plastový stojan pro TP-Link EAP610-Outdoor venkovní WiFi jednotku. Stojan umožňuje instalace na strop (rozměr podstavce je 83x100mm) nebo na stůl. Patice držáku umožňuje bezproblémové držení EAP jednotky, ať už je držák na stole či na stropě. Rozměry d...

Plastový stojan pro TP-Link EAP235-Wall a EAP615-Wall WiFi Access point jednotky. Stojan umožňuje instalace na stůl (rozměr podstavce je 81x120mm). Celkové rozměry stojanového držáku jsou 81 x 120 x 88 mm a je vyroben z šedého PETG fillamentu pomocí 3D...

Plastový držák je určený pro uchycení bezdrátových jednotek HALO H70X a HALO H80X značky MERCUSYS na stěnu a to pomocí dvou šroubů. Držák je vyroben z PETG materiálu na 3D tiskárně, má bílou barvu a celkové rozměry jsou 135 x 116 x 40mm.

The plastic holder is used for the horizontal installation of UniFi Access Points from Ubiquiti U6+, U6-Lite, UAP-nanoHD and UAP-AC-Lite on the wall or as a stand on a table. The holder can be installed with the UniFi plate up

The plastic holder is used for horizontal installation of UniFi Access Points from Ubiquiti U6-PRO and UAP-AC-PRO on the wall or as a stand on a table. The holder can be installed with the UniFi plate up and down and

Plastový držák je určený pro uchycení bezdrátových jednotek HX220 a HC220 značky TP-Link na stěnu a to pomocí dvou šroubů. Držák je vyroben z PETG materiálu na 3D tiskárně, má bílou barvu a celkové rozměry jsou 110 x 140 x 40mm.

Plastový držák je určený pro uchycení vybraných TP-Link produktů (viz níže) do 19" a 10" racku . V případě uchycení do 19" racku je možnost uchycení vpravo, vlevo nebo dvou držáků vedle sebe. Vnitřní rozměry rámečku jsou 226 x 131 x 35mm. Kompatibilní ...

The plastic wall mount is designed to mount Halo H50 / H30 / S12 / S3 Mesh Access Points from Mercusys. The holder is made using 3D printing, has a white color and its dimensions are 123 × 40 × 91mm.

The holder is designed to attach TP-Link Deco X20, Deco X50 and X60 wireless units to the wall using two screws. The holder is made of PETG material on a 3D printer and the colour is white.

The plastic holder is designed to hold selected TP-Link products (see below) in 19" and 10" racks. In the case of mounting in a 19" rack, it is possible to mount on the right, left or two holders next to each other. The internal dime

The plastic holder is designed to hold selected TP-Link products (see below) in 19" and 10" racks. In the case of mounting in a 19" rack, it is possible to mount on the right, left or two holders next to each other. The internal dime

The plastic holder is designed to mount the UCK-G2-PLUS from Ubiquiti to 19" and 10" racks. In the case of mounting in a 19" rack, it is possible to mount on the right, left or two holders next to each other.

The plastic holder/stand is designed to mount selected TP-Link EAP products (see below) on a table or wall. 3 holes are made in the base measuring 83 × 100 mm to attach the bracket to the wall. The overall dimensions of the holder are

The plastic holder is designed to hold selected MikroTik products (see below) in 19" and 10" racks. In the case of mounting in a 19" rack, it is possible to mount on the right, left or two holders next to each other. The internal dime

Plastový držák je určený pro uchycení vybraných MikroTik produktů (viz níže) do 19" a 10" racku . V případě uchycení do 19" racku je možnost uchycení vpravo, vlevo nebo dvou držáků vedle sebe. Vnitřní rozměry rámečku jsou 119 x 33 mm. Kompatibilní se z...

The holder is designed for attaching TP-Link Deco M9 wireless units to a ceiling or wall using a single screw. The holder is made of PETG material on a 3D printer in a white colour.

NanoHD-RCM-3 is a three-pack of ceiling mounts for UAP nanoHD, U6-Lite, U6-Lite or U6+, thanks to which you can embed your devices in the ceiling. Both packaging (3) ceiling mount

NanoHD-RetroFit-3 is a mounting kit for attaching the UAP-nanoHD unit to the wall or ceiling with the original UAP, UAP-LR mounts. Once mounted, your UAP-nanoHD, U6 Lite or U6+ will blend in with the walls because the Retrofit Mount kit elimina

Twin Horn Bracket allows you to install two symmetrical Horn antennas with exactly the same alignment. The bracket also accommodates mainstream 4x4 radios, such as ePMP™ 3000 or Mimosa® A5c. High density sectors or 4x4 deployments are now ingeniously s

EasyBracketTM for ePMPTM allows the installation of ePMP1000TM Radios to Ubiquiti AirMAX Sectors, RF elements Sectors and other antennas with compatible radio quick-mounting system. EasyBracket for ePMP is made of high quality Polycarbonate. Installati

NBE-WMK Wall Mount Kit is for enhanced stability when mounting the NanoBeam on a wall.

Precision Alignment Kit to better attach the antenna. Precision two-axis alignment enhances beam directivity for maximum PtP or backhaul performance. Applies to the following models airFiber®AF-5G30-S45 PowerBeam ™

Excellent plastic holder designed for places where it is not possible to drill, so thanks to the suction cup it can be mounted from the inside of the window. The bracket is compatible with NBE-5AC-16 and NBE-M5-16.