MikroTik

Now we offer 2.4Ghz 5dBi Dipole antennas with RPSMA connectors! Take BaseBox2 and simply attach two of those antennas on connectors of BaseBox2 to have 2x2 MIMO 2.4Ghz AP! By this you can have "2.4Ghz OmniTik", ideal for Outdoor Campus areas, for examp

R11e-2HnD is a Low-profile Lower power version of our 2.4Ghz miniPCIe card - it has a small heat-sink, u.Fl connector and less output power (800mW). Low profile is useful if you need to install the card in device like a laptop.

S+31DLC10D is a singlemode 10G SFP+ module with 1310nm wave length and 2 LC connectors for link distances up to 10km.

The RB912 in an outdoor enclosure, fit with two RPSMA connectors for antennas, and a cable hood for protection against moisture. Also available are three additional places for antenna connectors, in case you wish to use the RB912 miniPCIe slot for one

MikroTik UP1302C-12 is a replacement internal power supply that is specially designed for some MikroTik devices. Total power is 130W at 12V and 10.8A max. current. Compatibility list CCR1036-8G-2S+EM (rev. 2) CCR1

The Cloud Hosted Router (CHR) license is designed for installation in a virtual environment (VMWare, Hyper-V, VirtualBox, KVM and others). The P1 license has a speed limit of 1 Gbit for uploading to the interface and the lossy parameters are based on t

The Cloud Hosted Router (CHR) license is designed for installation in a virtual environment (VMWare, Hyper-V, VirtualBox, KVM and others). The P10 license has a speed limit of 10 Gbit for uploading to the interface and the lossy parameters are based on

The Cloud Hosted Router (CHR) license is designed for installation in a virtual environment (VMWare, Hyper-V, VirtualBox, KVM and others). The PU license does not have a speed limit, other parameters are based from the L6 license. Minimum

MikroTik K-65 is a set of rack-mount ears used to mount your RB4011 into a 19" rack. Due to the very low clearance height of the RouterBOARD, it only takes 1U.

±48 V DC telecom Open Frame Power supply with 12 V 8 A output, for use with new “r2” revision of Cloud Core Routers. Simply remove one of the current power supplies and replace with the new PW48V-12V85W for -48 V installations. Compatibility

The GPEN11 is a power injector that can be mounted on a wall, and will power your uplink devices with PoE power. MikroTik GPEN The GPEN11 is part of the GPEN (Giga

nRayAIM-DH1 is an alignment and aiming attachment for the nRAY. Use it to attach a scope of your choice for even greater precision and easier installation of the Wireless Wire nRAY. *Scope is not included.

The S-55DLC80D is a singlemode Gigabit SFP module with a 1550nm wavelength, two LC connectors and maximum distance up to 80km. The module iscompatible with all MikroTik products, that have SFP or SFP+ cages and other cisco compliant devices.

The RB4011 wall mount kit is made for protecting your device and it’s ethernet ports from unauthorised access. Made from durable steel, the mount attaches to a wall and allows the ethernet cables to be plugged in, before the router is mounted inside. T

DINrail PRO is a mounting bracket for LtAP mini series products, designed to fit standard 35 mm × 7.5 mm DIN rails. This bracket will allow to install LtAP mini next to the industrial control equipment like water meters etc., as well as in equipment ra

The CRS328-4C-20S-4S+RM is a 28 independent port switch with a combo group. This device has twenty SFP ports, four SFP+ ports for 10G modules and four combo ports, where you can choose to use SFP or RJ45 ports from the combo group. These ports can also

Cable reduction from MMCX to RSMA female, 26 cm long, intended for the frequency band from 2 to 6 GHz. The MMCX connector is angled and the RSMA female is straight. This is a high-quality connection, e.g. in BaseBox2 or BaseBox5 devic

The CWDM is a passive MUX/DEMUX unit, which allows to combine up to eight fiber links into one, to simplify and reduce the cost of long distance fiber installations. At the other location, the combined line is split back up again, so that instead of ei

S-C53DLC40D is a singlemode 1.25G SFP CWDM module with a 1530nm wavelength and two LC connectors for connection up to 40km. CWDM in your network will allow you to Increase efficiency of existing fiber network Prov

S-C57DLC40D is a singlemode 1.25G SFP CWDM module with a 1570nm wavelength and two LC connectors for connection up to 40km. CWDM in your network will allow you to Increase efficiency of existing fiber network Prov

S-C61DLC40D is a singlemode 1.25G SFP CWDM module with a 1610nm wavelength and two LC connectors for connection up to 40km. CWDM in your network will allow you to Increase efficiency of existing fiber network Prov

The S-4554LC80D is sold as a kit of two single mode WDM modules with Gigabit speed, one LC connector on each side and maximum distance up to 80km. The wavelengths of the modules are 1490 / 1550nm and 1550 / 1490nm.

The wireless wire offers blazing fast Gigabit speeds for transparent connectivity between two locations, without any sacrifice in your LAN speeds. Simply point the included devices at one another and power them on, they are already preconfigured

The new RB1100AHx4 series of devices uses a new quad core Cortex A15 chip from Annapurna labs, an Amazon company, The chip is clocked at 1.4 GHz, for a maximum throughput of up to 7.5 Gbps. The RB1100AHx4 supports IPsec hardware acceleratio

We are now offering a Hot Swap -48V DC telecom power supply (product code PW48V-12V150W), available to purchase separately for use with CCR1072. Simply remove one of the current power supplies and replace with the new PW48V-12V150W for -48V installatio

mANT30 is a professional class 5 GHz 30dBi dish antenna, built to the highest industry standards. Built to seamlessly accomodate our Basebox series products, but can be used for any pole mounted wireless device due to the adequate length of the include

Kit contains two SFP+ modules that can be used as a pair to achieve operating data rate up to 25 Gbps for distances up to 15km on a single optical cable. SFP/ SFP+/ SFP28.

Outdoor AC/DC power supply in a durable metal chassis with output voltage 26 V, max. output current 9.4 A, total power 250 W suitable for a series of netPower products from MikroTik. The chassis is IP67 certified with extra protec

No need to buy several antennas for your Internet-of-things setups – just grab the new HGO-LTE-W antenna that can handle an impressive frequency spectrum 699MHz – 3,8GHz. That’s right – you can use the same antenna for LTE, CAT-M/NB and LoRa con

Bluetooth tags play a huge role in IoT setups, where Bluetooth is used to broadcast the data over short distances. You can use these small devices for proximity-based tracking of various objects. For example, if you have a KNOT gateway in