MikroTik

The CWDM is a passive MUX/DEMUX unit, which allows to combine up to eight fiber links into one, to simplify and reduce the cost of long distance fiber installations. At the other location, the combined line is split back up again, so that instead of ei

S-C53DLC40D is a singlemode 1.25G SFP CWDM module with a 1530nm wavelength and two LC connectors for connection up to 40km. CWDM in your network will allow you to Increase efficiency of existing fiber network Prov

S-C57DLC40D is a singlemode 1.25G SFP CWDM module with a 1570nm wavelength and two LC connectors for connection up to 40km. CWDM in your network will allow you to Increase efficiency of existing fiber network Prov

S-C59DLC40D is a singlemode 1.25G SFP CWDM module with a 1590nm wavelength and two LC connectors for connection up to 40km. CWDM in your network will allow you to Increase efficiency of existing fiber network Prov

S-C61DLC40D is a singlemode 1.25G SFP CWDM module with a 1610nm wavelength and two LC connectors for connection up to 40km. CWDM in your network will allow you to Increase efficiency of existing fiber network Prov

The S-4554LC80D is sold as a kit of two single mode WDM modules with Gigabit speed, one LC connector on each side and maximum distance up to 80km. The wavelengths of the modules are 1490 / 1550nm and 1550 / 1490nm.

OmniTIK 5 ac is an outdoor access point with two built-in omni-directional 5 GHz antennas with a 7,5dBi gain, 5x Gigabit LAN and one USB port for 3G/4G modem. Omnitik 5 ac supports 802.11a/n/ac wireless standards, transmissi

LDF 5 or "Lite dish feed" is a very specific outdoor CPE device with two built-in antennas with 9dBi gain. LDF 5 was designed for mounting on satellite dish antenna instead of the original feed LNB with 40 mm mounting. Antenna gain maybe increas

CA411-711 is new indoor case for RB411, RB911, RB912 and RB922 series. It has changeable front panels, so you can choose one that fits the product that you actually use. Also, case is higher to accommodate high-power wireless cards and has wall mountin

The Light Head Grid (LHG) is a compact and light wireless device with an integrated 24.5 dBi grid antenna at a revolutionary price. It is perfect for point to point links or for use as a CPE at longer distances. The gr

12POW150 is replacement Hot Swap power source for MikroTik CCR1072-1G-8S+. Total output power is 150W.

It reduces wind load, protects reflector surfaces from harsh environment, protects the antenna feed from falling objects, as well as positively affects the antenna sustainability and operational life. It's made from a special material that has a low di

ODR-OmniTik is an interference suppression cover made from stainless steel with a thickness of 0.8 mm designed for MikroTik OmniTik U/UPA units. This cover reduces unwanted interference, reducing noise, increasing connection stabil

Odrušovač pro MikroTik RouterBOARD SEXTANTG-5HPnD snižuje nežádoucí interferenční rušení ze zadní strany a z bočních stran. Ochraňuje signál jen v žádoucí oblasti. Odrušovač spolu se zadním krytem nezvyšuje zisk antény, avšak výrazně snižuje nežádoucí ...

The CA600 mounting box is designed for the MikroTik RB600 and RB800. The box has perforations on the sides for heat dissipation, on the front box has 3 holes for LAN, serial port, power jack and diodes. On the back there are 4 holes for R

The license key for your installed RouterOS on RouterBOARD or x86 platform. Differences between different levels of license, we recommend you take a look here.

The license key for your installed RouterOS on RouterBOARD or x86 platform. Differences between different levels of license, we recommend you take a look here.

The license key for your installed RouterOS on RouterBOARD or x86 platform. Differences between different levels of license, we recommend you take a look here.

It is a special key which is issued by the Support Team if you accidently lose the license, and the Mikrotik Support decides that it is not directly your fault. This key has the same features as the key that you lose. Note that before issuing such key,

R11e-2HPnD is our new 802.11b/g/n Dual Chain high power 1000mW miniPCI-e card, operating in full 2192-2732 MHz frequency. Ideally suited for the new RB912 series, RB800 or our new miniPCIe adapters - RB14e/RB14eU. Unit is equipped with two MMCX connect

R11e-2HnD is a Low-profile Lower power version of our 2.4Ghz miniPCIe card - it has a small heat-sink, u.Fl connector and less output power (800mW). Low profile is useful if you need to install the card in device like a laptop.

High power 4920-5920MHz 802.11a/n dual chain wireless card in miniPCI-e format. Ideally suited for the new RB912 series, RB800 or our new miniPCIe adapter card - RB14e. The card features built-in LED indicators for wireless mode, connection s

Now we offer 2.4Ghz 5dBi Dipole antennas with RPSMA connectors! Take BaseBox2 and simply attach two of those antennas on connectors of BaseBox2 to have 2x2 MIMO 2.4Ghz AP! By this you can have "2.4Ghz OmniTik", ideal for Outdoor Campus areas, for examp

CA150 is a mounting box from MikroTik for indoor use and is intended only for MikroTik RouterBOARD models RB450, RB450G and RB850Gx2. There are molded holes for 5 Ethernet ports on the side and a hole for the power jack and RS232 seri

Replacement holder for RouterBOARD SXT models. Suitable for all models.

The new AC standard is here, with up to 866Mbit over the air datarate, 256-QAM modulation, and 80MHz channels. 802.11ac opens up new possibilities and speeds never possible before. The SXT ac is a new member in our 802.11ac product lineup, cu

This NetMetal version is equipped with a miniPCI-express slot a SIM slot for 3G/4G device or additional wireless card, a high power 2x2 dual chain 802.11ac wireless and two RP-SMA connectors for external antennas. The NetMetal i

The ATL LTE18 kit is a device used to connect to a mobile 3G/LTE network. Put it outside on a pole or just in a high enough place and it's there where cell phones don't have a signal. Thanks to a large radome antenna